SPILFYTER¨ Products Page 1 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
Section 1. Chemical Product and Company Identification
Product Number: S2 Series
Product Name: HAZMAT Sorbent Products
Manufacturer: Emergency Telephone Numbers:
NPS Corporation CHEMTREC--Domestic (800)424-9300 24 hours
3303 Spirit Way --International (202)483-7616 24 hours
Green Bay, WI 54304 Information (800) 558-5066 7:30am-4:30pm CDT M-F
Section 2. Composition/Information on Ingredients
CAS Registry # Component
9003-07-0 Polypropylene Particulate or Fabric 98.7%
---NA--- Yellow Pigment 0.3%
---NA--- Surfactant 1.0%
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
Section 3. Hazards Identification
Emergency OverviewOdorless, white or colored fabric or particulate. This material presents little or no hazard if spilled and exhibits no unusual fire hazard.
|
Potential Health Effects
Eye: Direct contact may cause irritation.
Inhalation: Exposure to dust levels exceeding the PEL (see Section 8) may cause irritation of the
upper respiratory system. Breathing dust may aggravate acute or chronic asthma or
other chronic pulmonary diseases.
Signs and Symptoms:
á Eyes: Redness, Tearing
á Inhalation: Dry cough, labored breathing during exertion
Section 4. First Aid Measures
Eyes: Immediately flush with plenty of water for at least 15 minutes. If irritation persists, seek medical
attention.
Skin: Brush off excess fibers with dry towel. Wash affected area with plenty of soap and water for several
minutes. If skin irritation develops or persists, seek medical attention.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Seek medical attention.
NOTE: If burned through contact with molten material, cool as quickly as possible with water and seek
medical attention. Do not attempt to remove the cooled molten material.
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 2 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
Section 5. Fire Fighting Measures
Flash Point: >625 ¡F
Flammable Limits: NA
Auto-ignition Temperature: >675 ¡F
NOTE: This material will burn, but it is difficult to ignite.
Extinguishing Media: Water spray, ABC dry chemical, foam, or carbon dioxide. Use water fog or spray to cool exposed equipment and containers.
Special Fire Fighting Procedures: For large fires or fires in confined areas, full emergency equipment with
self-contained breathing apparatus and full protective clothing should be
used. Thermal decomposition of this product may produces hazardous
and irritating gases. See Section 10.
Section 6. Accidental Release Measures
Unused material can be shoveled, swept, or vacuumed and recycled for use. Avoid generating airborne dust.
If used material is released or spilled, see Section 13.
Section 7. Handling and Storage
Store at room temperature in a dry area. When handling, avoid the generation of airborne dust. Storage for
extended periods (>30 days) at temperatures >150 ¡F may cause decomposition. This material produces an
electrostatic accumulation hazard. Use proper grounding/bonding procedures.
Section 8. Exposure Controls/Personal Protection
Exposure Limits: None specifically developed for this product; treated as a nuisance dust as defined in
29 CFR 1910.1000.
OSHA PEL: Total Dust is 15 mg/M3.
Respirable Fraction is 5mg/M3.
ACGIH TLV is 10 mg/M3.
The end-user must determine the specific types of personal protective equipment needed according to 29 CFR 1910.132—Personal Protective Equipment (PPE) for General Industry. The following are only suggestions:
á Eyes: Safety glasses or goggles
á Skin: Work gloves
Adequate ventilation should be provided to limit the amount of airborne dust.
Section 9. Physical and Chemical Properties
Appearance: White or colored fabric or particulate
Odor: Odorless Evaporation Rate (Butyl Acetate=1): NA
Boiling Point: NA % Vaporizable by volume (H2O=100): <0.4
Vapor Pressure (mmHg): NA
Vapor Density: NA
Solubility in Water: Insoluble
Specific Gravity (H2O=1): 0.90
Melting Point: >320 ¡F
pH: NA
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 3 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
Section 10. Stability and Reactivity
Stable: Yes
Conditions to Avoid: See Section 7
Incompatibility (Materials to Avoid): Avoid contact with hot or concentrated nitric and perchloric acids,
and fuming sulfuric acid at temperatures >140 ¡F
Hazardous Decomposition or Byproducts: Thermal decomposition produces carbon monoxide, carbon
dioxide, methane, acetone, and other ketones.
Hazardous Polymerization: Will not occur
Section 11. Toxicological Information
This product is not listed by NTP or IARC. See Section 15.
Section 12. Ecological Information
No data available. See Section 15.
Section 13. Disposal Considerations
This product in itself is considered to be non-hazardous as defined by RCRA (40 CFR 261). Once used, this
product will take on the characteristics of the chemical sorbed and should be disposed of accordingly.
Disposal of this product (used or unused) must be in compliance with all local, state, and federal regulations.
Section 14. Transport Information
This product is not a DOT Hazardous Material and is not regulated for all shipping purposes.
Section 15. Regulatory Information
This product does not meet the definition of a hazardous chemical given in 29 CFR 1910.1200 (OSHA).
TSCA Inventory Status: All components are listed on the TSCA list.
SARA Title III
Section 302 Extreme Hazardous Substance List: Not listed
Section 311/312 Hazard Classification:
Immediate (acute): No
Delayed (chronic): No
Fire: No
Sudden Release of Pressure: No
Reactive: No
Section 313 Toxic Chemicals: Not listed
USEPA CERCLA—Reportable Quantity (RQ): Not listed
RCRA Hazardous Waste: Not listed
State/IntÕl Right-to-Know Regulations: Not listed
Section 16. Other Information
Abbreviations:
CFR: Code of Federal Regulations
OSHA: Occupational Safety and Health Administration
MSDS: Material Safety Data Sheet
PEL: Permissible Exposure Limit
NA: Not Applicable
ACGIH: American Conference of Governmental Industrial Hygienists
TLV: Threshold Limit Value
NTP: National Toxicology Program
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 4 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
Abbreviations (cont.):
IARC: International Agency for Research on Cancer
RCRA: Resource Conservation and Recovery Act
TSCA: Toxic Substances Control Act
SARA: Superfund Amendments and Reauthorization Act
USEPA: United States Environmental Protection Agency
CERCLA: Comprehensive Response, Compensation, and Liability Act
DOT: Department of Transportation
NFPA: National Fire Protection Association
HMIS: Hazardous Material Information System
NFPA Ratings: HMIS Ratings:
Health: 0 Health: 0
Fire: 1 Flammability: 1
Reactivity: 0 Reactivity: 0
Special Hazard: None Personal Protection: NA
NOTE: This MSDS has been prepared only for the Hazmat Sorbent Products (S2 Series) of SPILFYTER¨ Products. The MSDSÕs of the chemicals used with this product must be reviewed completely, and precautions taken as described.
The information accumulated herein has been compiled from sources believed to be reliable and is accurate to the best of our knowledge. However, NPS Corporation cannot give guarantees regarding the information from sources, and expressly does not make any warranties, nor assumes any liability for its uses of this product.
Disclaimer
You have purchased SPILFYTER¨ products from NPS Corporation
You have been provided data, product labels, MSDSÕs, and other information about SPILFYTER¨ Products.
Some SPILFYTER¨ Products are hazardous. Information about SPILFYTER¨ Products that are hazardous is furnished without guarantee. NPS Corporation does not guarantee the accuracy of the information about hazardous SPILFYTER¨ Products.
Those products are only to be used by people having expertise in using the hazardous products.
The information provided about the hazardous products is believed to be correct. You must perform your investigation as to the safety, toxicity, suitability, and proper shipping method for any hazardous SPILFYTER¨ Product.
No guarantee, expressed or implied, is made by NPS Corporation about the results of use of its products. No guarantee is made as to the safety and toxicity of any SPILFYTER¨ Product.
NPS Corporation does not assume any liability arising out of use of SPILFYTER¨ Products. Additional information and research may be necessary before you use the SPILFYTER¨ Products. NPS Corporation is not responsible for damages, direct or indirect, resulting from the use of SPILFYTER¨ Products or from reliance on data in the MSDS or product label.
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 5 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
If you resell SPILFYTER¨ Products, you must, by law, furnish your customers a copy of MSDSÕs and handling instructions.
You are also required by law to insure that all SPILFYTER¨ Products are properly shipped.
SPILFYTER¨, KOLLECT-A-KEM¨, HANDS-IN-BAG¨, KOLORSAFE¨, and GRAB&GO¨ are all registered trademarks of NPS Corporation
AQUALOCKITª, TRUK-KIT ª, DRAINGUARDª, GAPSEALª, MEDICLEANª, and TIDYMATª, are all trademarks of NPS Corporation
© Copyright 2002, NPS Corporation
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 1 of 5
AQUALOCKIT¨ Revision Date: 03/31/05
MSDS No. 1016
Section 1. Chemical Product and Company Identification
Product Number: 6700 Series
Product Name: AQUALOCKITª--Super Polymer
Manufacturer: Emergency Telephone Numbers:
NPS Corporation CHEMTREC--Domestic (800)424-9300 24 hours
3303 Spirit Way --International (202)483-7616 24 hours
Green Bay, WI 54304 Information (800) 558-5066 7:30am-4:30pm CDT M-F
Section 2. Composition/Information on Ingredients
CAS Registry # Component
25608-12-2 Potassium Polyacrylate
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
Section 3. Hazards Identification
Emergency OverviewOdorless, white crystalline solid. This material presents little or no hazard if spilled and exhibits no unusual fire hazard.
|
Potential Health Effects
NOTE: This product polymerizes water. Avoid contact with eyes and mucous membranes.
Eye: May cause irritation.
Skin: May cause irritation.
Inhalation: Exposure to dust levels exceeding the PEL (see Section 8) may cause irritation to the upper
respiratory system.
Signs and Symptoms:
á Eyes: Redness, Tearing
á Skin: Redness
á Inhalation: Shortness of breath, Labored breathing
Section 4. First Aid Measures
Eyes: Immediately flush with plenty of water for at least 15 minutes. If irritation persists, seek medical
attention.
Skin: Brush off excess powder with a dry towel. Wash affected area with plenty of soap and water for several minutes. If skin irritation develops or persists, seek medical attention.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Seek medical attention.
Ingestion: If swallowed, call a physician or poison control center immediately.
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 2 of 5
AQUALOCKIT¨ Revision Date: 03/31/05
MSDS No. 1016
Section 5. Fire Fighting Measures
Flash Point: NA
Flammable Limits: NA
Auto-ignition Temperature: NA
NOTE: This material is non-combustible as supplied and will not support combustion. This material is
slippery when wet.
Extinguishing Media: Any extinguishing media can be used for the packaging.
Special Fire Fighting Procedures: For large fires or fires in confined areas, full emergency equipment with
self-contained breathing apparatus and full protective clothing should be used. Thermal decomposition will produce carbon monoxide, carbon dioxide, and hydrocarbons.
Section 6. Accidental Release Measures
Avoid breathing or generating airborne dust. Avoid using water. Avoid contact with eyes and mucous membranes. If unused material is spilled, collect by sweeping, shoveling or vacuuming and recycle the material for use . If this product is mixed with other materials, see Section 13.
Section 7. Handling and Storage
Store in a cool, dry, and well ventilated area.
Section 8. Exposure Controls/Personal Protection
Exposure Limits: None specifically developed for this product; treated as a nuisance dust as defined in 29 CFR 1910.1000.
OSHA PEL: Total Dust is 15 mg/M3.
Respirable Fraction is 5mg/M3.
ACGIH TLV is 10 mg/M3.
The end-user must determine the specific types of personal protective equipment needed according to 29 CFR 1910.132—Personal Protective Equipment (PPE) for General Industry. The following are only suggestions:
á Eyes: Safety glasses or goggles
á Skin: Suitable chemically resistant gloves and protective clothing
á Inhalation: Air purifying respirator with appropriate filter for nuisance dust.
Adequate ventilation should be provided to limit the threat of inhalation.
Section 9. Physical and Chemical Properties
Appearance: White crystalline solid
Odor: Odorless
Boiling Point: NA
Vapor Pressure (mmHg): NA
Vapor Density: NA
Solubility in Water: Insoluble—polymerizes water
Specific Gravity (H2O=1): 0.90
Melting Point: NA
pH: NA
Evaporation Rate (Butyl Acetate=1): NA
% Vaporizable by volume (H2O=100): NA
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 3 of 5
AQUALOCKIT¨ Revision Date: 03/31/05
MSDS No. 1016
Section 10. Stability and Reactivity
Stable: Yes
Conditions to Avoid: None known
Incompatibility (Materials to Avoid): Strong oxidizers
Hazardous Decomposition or Byproducts: Thermal decomposition produces carbon monoxide, carbon
dioxide, and hydrocarbons.
Hazardous Polymerization: Will not occur
Section 11. Toxicological Information
This product is not listed by NTP or IARC. See Section 15.
Section 12. Ecological Information
No data available. See Section 15.
Section 13. Disposal Considerations
This product in itself is considered to be non-hazardous as defined by RCRA (40 CFR 261). Once used, this
product may take on the characteristics of the chemical(s) sorbed and should be disposed of accordingly. Disposal of this product (used or unused) must be in compliance with all local, state, and federal regulations.
Section 14. Transport Information
This product is not a DOT Hazardous Material and is not regulated for all shipping purposes.
Section 15. Regulatory Information
TSCA Inventory Status: All components are listed on the TSCA list.
SARA Title III
Section 302 Extreme Hazardous Substance List: Not listed
Section 311/312 Hazard Classification:
Immediate (acute): No
Delayed (chronic): No
Fire: No
Sudden Release of Pressure: No
Reactive: No
Section 313 Toxic Chemicals: Not listed
USEPA CERCLA—Reportable Quantity (RQ): Not listed
RCRA Hazardous Waste: Not listed
State/IntÕl Right-to-Know Regulations: Not listed
Section 16. Other Information
Abbreviations:
CFR: Code of Federal Regulations
OSHA: Occupational Safety and Health Administration
MSDS: Material Safety Data Sheet
PEL: Permissible Exposure Limit
NA: Not Applicable
ACGIH: American Conference of Governmental Industrial Hygienists
TLV: Threshold Limit Value
NTP: National Toxicology Program
IARC: International Agency for Research on Cancer
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 4 of 5
AQUALOCKIT¨ Revision Date: 03/31/05
MSDS No. 1016
Abbreviations (cont.):
RCRA: Resource Conservation and Recovery Act
TSCA: Toxic Substances Control Act
SARA: Superfund Amendments and Reauthorization Act
USEPA: United States Environmental Protection Agency
CERCLA: Comprehensive Response, Compensation, and Liability Act
DOT: Department of Transportation
NFPA: National Fire Protection Association
HMIS: Hazardous Material Information System
NFPA Ratings: HMIS Ratings:
Health: 1 Health: 1
Fire: 0 Flammability: 0
Reactivity: 0 Reactivity: 0
Special Hazard: None Personal Protection: X
NOTE: This MSDS has been prepared only for the AQUALOCKITª (6700 Series) of SPILFYTER¨ Products. The MSDSÕs of the chemicals used with this product must be reviewed completely, and precautions taken as described.
The information accumulated herein has been compiled from sources believed to be reliable and is accurate to the best of our knowledge. However, NPS Corporation cannot give guarantees regarding the information from sources, and expressly does not make any warranties, nor assumes any liability for its uses of this product.
Disclaimer
You have purchased SPILFYTER¨ products from NPS Corporation
You have been provided data, product labels, MSDSÕs, and other information about SPILFYTER¨ Products.
Some SPILFYTER¨ Products are hazardous. Information about SPILFYTER¨ Products that are hazardous is furnished without guarantee. NPS Corporation does not guarantee the accuracy of the information about hazardous SPILFYTER¨ Products.
Those products are only to be used by people having expertise in using the hazardous products.
The information provided about the hazardous products is believed to be correct. You must perform your investigation as to the safety, toxicity, suitability, and proper shipping method for any hazardous SPILFYTER¨ Product.
No guarantee, expressed or implied, is made by NPS Corporation about the results of use of its products. No guarantee is made as to the safety and toxicity of any SPILFYTER¨ Product.
.NPS Corporation does not assume any liability arising out of use of SPILFYTER¨ Products. Additional information and research may be necessary before you use the SPILFYTER¨ Products. NPS Corporation
is not responsible for damages, direct or indirect, resulting from the use of SPILFYTER¨ Products or from reliance on data in the MSDS or product label.
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 5 of 5
AQUALOCKIT¨ Revision Date: 03/31/05
MSDS No. 1016
If you resell SPILFYTER¨ Products, you must, by law, furnish your customers a copy of MSDSÕs and handling instructions.
You are also required by law to insure that all SPILFYTER¨ Products are properly shipped.
SPILFYTER¨, KOLLECT-A-KEM¨, HANDS-IN-BAG¨, KOLORSAFE¨, and GRAB&GO¨ are all registered trademarks of NPS Corporation
AQUALOCKITª, TRUK-KIT ª, DRAINGUARDª, GAPSEALª, MEDICLEANª, and TIDYMATª are all trademarks of NPS Corporation
Copyright 2001, NPS Corporation
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 1 of 5
Decon Solution 1 Revision Date: 07/17/02
MSDS No. 1018
Section 1. Chemical Product and Company Identification
Product Number: 680041
Product Name: Decon Solution 1—1st Wash for Unknown Contaminants
Manufacturer: Emergency Telephone Numbers:
NPS Corporation CHEMTREC--Domestic (800)424-9300 24 hours
3303 Spirit Way --International (202)483-7616 24 hours
Green Bay, WI 54304 Information (800) 558-5066 7:30am-4:30pm CDT M-F
Section 2. Composition/Information on Ingredients
CAS Registry # Component
497-19-8 Sodium Carbonate, anhydrous
6834-92-0 Sodium Metasilicate
77-09-8 Phenolphthalien
7732-18-5 Water
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
Section 3. Hazards Identification
Emergency OverviewOdorless, pink liquid. This material presents little or no hazard if spilled and exhibits no unusual fire hazard.
|
Potential Health Effects
Eye: May cause irritation.
Skin: May cause irritation. Repeated skin contact may aggravate an existing dermatitis (skin
condition) and/or sensitivity of the skin.
Inhalation: May cause irritation to the upper respiratory system.
Signs and Symptoms:
á Eyes: Redness, Tearing
á Skin: Redness
á Inhalation: Coughing, Shortness of breath
á Ingestion: Nausea, Vomiting, Diarrhea
Section 4. First Aid Measures
Eyes: Immediately flush with plenty of water for at least 15 minutes. If irritation persists, seek medical
attention.
Skin: Remove contaminated clothing. Wash affected area with plenty of soap and water for several
minutes. If skin irritation develops or persists, seek medical attention.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Seek medical attention.
Ingestion: If swallowed, call a physician or poison control center immediately.
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 2 of 5
Decon Solution 1 Revision Date: 07/17/02
MSDS No. 1018
Section 5. Fire Fighting Measures
Flash Point: NA
Flammable Limits: NA
Auto-ignition Temperature: NA
NOTE: This material is non-combustible as supplied and does not support combustion.
Extinguishing Media: If the need exists, water spray, dry chemical foam, or carbon dioxide can be used.
Special Fire Fighting Procedures: For large fires or fires in confined areas, full emergency equipment with self-contained breathing apparatus and full protective clothing should be used.
Section 6. Accidental Release Measures
Avoid breathing vapors. Avoid contact with skin and eyes. Contain the spill and collect the material using chemically resistant sorbent products. If this product is mixed with other materials, see Section 13.
Section 7. Handling and Storage
Store in at temperatures >32 ¡F in a well-ventilated area. Keep containers tightly closed.
NOTE: If this product is stored at temperatures >150 ¡F or at elevations above 5000 feet, gas may form, increasing the pressure within the container, causing the container to bulge. If bulging occurs, remove the container from the work area and slowly open the container to release the gas. Be sure to wear proper personal protective equipment.
Section 8. Exposure Controls/Personal Protection
Exposure Limits: There are no exposure limits established for any component of this product.
The end-user must determine the specific types of personal protective equipment needed according to 29 CFR 1910.132—Personal Protective Equipment (PPE) for General Industry. The following are only suggestions:
á Eyes: Safety glasses, goggles, or face shield
á Skin: Suitable chemically resistant gloves and protective clothing
á Inhalation: If vapors or mists are present, air purifying respirator with appropriate chemical cartridge or canister.
Adequate ventilation should be provided to limit the threat of inhalation.
Section 9. Physical and Chemical Properties
Appearance: Pink liquid
Odor: Odorless
Boiling Point: Not Tested
Vapor Pressure (mmHg): Not Tested
Vapor Density: Not Tested
Solubility in Water: Soluble
Specific Gravity (H2O=1): 1.11
Freezing Point: Not Tested
pH: 12.1
Evaporation Rate (Butyl Acetate=1): Not Tested
% Vaporizable by volume (H2O=100): 100
Section 10. Stability and Reactivity
Stable: Yes
Conditions to Avoid: None known
Incompatibility (Materials to Avoid): Reacts with strong acids and fluorine. This material is corrosive to
aluminum, galvanized iron, zinc, and may generate hydrogen gas.
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products &nb