SPILFYTER¨ Products Page 1 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
Section 1. Chemical Product and Company Identification
Product Number: S2 Series
Product Name: HAZMAT Sorbent Products
Manufacturer: Emergency Telephone Numbers:
NPS Corporation CHEMTREC--Domestic (800)424-9300 24 hours
3303 Spirit Way --International (202)483-7616 24 hours
Green Bay, WI 54304 Information (800) 558-5066 7:30am-4:30pm CDT M-F
Section 2. Composition/Information on Ingredients
CAS Registry # Component
9003-07-0 Polypropylene Particulate or Fabric 98.7%
---NA--- Yellow Pigment 0.3%
---NA--- Surfactant 1.0%
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
Section 3. Hazards Identification
Emergency OverviewOdorless, white or colored fabric or particulate. This material presents little or no hazard if spilled and exhibits no unusual fire hazard.
|
Potential Health Effects
Eye: Direct contact may cause irritation.
Inhalation: Exposure to dust levels exceeding the PEL (see Section 8) may cause irritation of the
upper respiratory system. Breathing dust may aggravate acute or chronic asthma or
other chronic pulmonary diseases.
Signs and Symptoms:
á Eyes: Redness, Tearing
á Inhalation: Dry cough, labored breathing during exertion
Section 4. First Aid Measures
Eyes: Immediately flush with plenty of water for at least 15 minutes. If irritation persists, seek medical
attention.
Skin: Brush off excess fibers with dry towel. Wash affected area with plenty of soap and water for several
minutes. If skin irritation develops or persists, seek medical attention.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Seek medical attention.
NOTE: If burned through contact with molten material, cool as quickly as possible with water and seek
medical attention. Do not attempt to remove the cooled molten material.
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 2 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
Section 5. Fire Fighting Measures
Flash Point: >625 ¡F
Flammable Limits: NA
Auto-ignition Temperature: >675 ¡F
NOTE: This material will burn, but it is difficult to ignite.
Extinguishing Media: Water spray, ABC dry chemical, foam, or carbon dioxide. Use water fog or spray to cool exposed equipment and containers.
Special Fire Fighting Procedures: For large fires or fires in confined areas, full emergency equipment with
self-contained breathing apparatus and full protective clothing should be
used. Thermal decomposition of this product may produces hazardous
and irritating gases. See Section 10.
Section 6. Accidental Release Measures
Unused material can be shoveled, swept, or vacuumed and recycled for use. Avoid generating airborne dust.
If used material is released or spilled, see Section 13.
Section 7. Handling and Storage
Store at room temperature in a dry area. When handling, avoid the generation of airborne dust. Storage for
extended periods (>30 days) at temperatures >150 ¡F may cause decomposition. This material produces an
electrostatic accumulation hazard. Use proper grounding/bonding procedures.
Section 8. Exposure Controls/Personal Protection
Exposure Limits: None specifically developed for this product; treated as a nuisance dust as defined in
29 CFR 1910.1000.
OSHA PEL: Total Dust is 15 mg/M3.
Respirable Fraction is 5mg/M3.
ACGIH TLV is 10 mg/M3.
The end-user must determine the specific types of personal protective equipment needed according to 29 CFR 1910.132—Personal Protective Equipment (PPE) for General Industry. The following are only suggestions:
á Eyes: Safety glasses or goggles
á Skin: Work gloves
Adequate ventilation should be provided to limit the amount of airborne dust.
Section 9. Physical and Chemical Properties
Appearance: White or colored fabric or particulate
Odor: Odorless Evaporation Rate (Butyl Acetate=1): NA
Boiling Point: NA % Vaporizable by volume (H2O=100): <0.4
Vapor Pressure (mmHg): NA
Vapor Density: NA
Solubility in Water: Insoluble
Specific Gravity (H2O=1): 0.90
Melting Point: >320 ¡F
pH: NA
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 3 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
Section 10. Stability and Reactivity
Stable: Yes
Conditions to Avoid: See Section 7
Incompatibility (Materials to Avoid): Avoid contact with hot or concentrated nitric and perchloric acids,
and fuming sulfuric acid at temperatures >140 ¡F
Hazardous Decomposition or Byproducts: Thermal decomposition produces carbon monoxide, carbon
dioxide, methane, acetone, and other ketones.
Hazardous Polymerization: Will not occur
Section 11. Toxicological Information
This product is not listed by NTP or IARC. See Section 15.
Section 12. Ecological Information
No data available. See Section 15.
Section 13. Disposal Considerations
This product in itself is considered to be non-hazardous as defined by RCRA (40 CFR 261). Once used, this
product will take on the characteristics of the chemical sorbed and should be disposed of accordingly.
Disposal of this product (used or unused) must be in compliance with all local, state, and federal regulations.
Section 14. Transport Information
This product is not a DOT Hazardous Material and is not regulated for all shipping purposes.
Section 15. Regulatory Information
This product does not meet the definition of a hazardous chemical given in 29 CFR 1910.1200 (OSHA).
TSCA Inventory Status: All components are listed on the TSCA list.
SARA Title III
Section 302 Extreme Hazardous Substance List: Not listed
Section 311/312 Hazard Classification:
Immediate (acute): No
Delayed (chronic): No
Fire: No
Sudden Release of Pressure: No
Reactive: No
Section 313 Toxic Chemicals: Not listed
USEPA CERCLA—Reportable Quantity (RQ): Not listed
RCRA Hazardous Waste: Not listed
State/IntÕl Right-to-Know Regulations: Not listed
Section 16. Other Information
Abbreviations:
CFR: Code of Federal Regulations
OSHA: Occupational Safety and Health Administration
MSDS: Material Safety Data Sheet
PEL: Permissible Exposure Limit
NA: Not Applicable
ACGIH: American Conference of Governmental Industrial Hygienists
TLV: Threshold Limit Value
NTP: National Toxicology Program
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 4 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
Abbreviations (cont.):
IARC: International Agency for Research on Cancer
RCRA: Resource Conservation and Recovery Act
TSCA: Toxic Substances Control Act
SARA: Superfund Amendments and Reauthorization Act
USEPA: United States Environmental Protection Agency
CERCLA: Comprehensive Response, Compensation, and Liability Act
DOT: Department of Transportation
NFPA: National Fire Protection Association
HMIS: Hazardous Material Information System
NFPA Ratings: HMIS Ratings:
Health: 0 Health: 0
Fire: 1 Flammability: 1
Reactivity: 0 Reactivity: 0
Special Hazard: None Personal Protection: NA
NOTE: This MSDS has been prepared only for the Hazmat Sorbent Products (S2 Series) of SPILFYTER¨ Products. The MSDSÕs of the chemicals used with this product must be reviewed completely, and precautions taken as described.
The information accumulated herein has been compiled from sources believed to be reliable and is accurate to the best of our knowledge. However, NPS Corporation cannot give guarantees regarding the information from sources, and expressly does not make any warranties, nor assumes any liability for its uses of this product.
Disclaimer
You have purchased SPILFYTER¨ products from NPS Corporation
You have been provided data, product labels, MSDSÕs, and other information about SPILFYTER¨ Products.
Some SPILFYTER¨ Products are hazardous. Information about SPILFYTER¨ Products that are hazardous is furnished without guarantee. NPS Corporation does not guarantee the accuracy of the information about hazardous SPILFYTER¨ Products.
Those products are only to be used by people having expertise in using the hazardous products.
The information provided about the hazardous products is believed to be correct. You must perform your investigation as to the safety, toxicity, suitability, and proper shipping method for any hazardous SPILFYTER¨ Product.
No guarantee, expressed or implied, is made by NPS Corporation about the results of use of its products. No guarantee is made as to the safety and toxicity of any SPILFYTER¨ Product.
NPS Corporation does not assume any liability arising out of use of SPILFYTER¨ Products. Additional information and research may be necessary before you use the SPILFYTER¨ Products. NPS Corporation is not responsible for damages, direct or indirect, resulting from the use of SPILFYTER¨ Products or from reliance on data in the MSDS or product label.
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 5 of 5
Hazmat Sorbents Revision Date: 07/25/05
MSDS No. 1003
If you resell SPILFYTER¨ Products, you must, by law, furnish your customers a copy of MSDSÕs and handling instructions.
You are also required by law to insure that all SPILFYTER¨ Products are properly shipped.
SPILFYTER¨, KOLLECT-A-KEM¨, HANDS-IN-BAG¨, KOLORSAFE¨, and GRAB&GO¨ are all registered trademarks of NPS Corporation
AQUALOCKITª, TRUK-KIT ª, DRAINGUARDª, GAPSEALª, MEDICLEANª, and TIDYMATª, are all trademarks of NPS Corporation
© Copyright 2002, NPS Corporation
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 1 of 5
KOLORSAFE¨ Dry Acid Neutralizer Revision Date: 07/20/05
MSDS No. 1008
Section 1. Chemical Product and Company Identification
Product Number: 4400 Series
Product Name: KOLORSAFE¨ Dry Acid Neutralizer
Manufacturer: Emergency Telephone Numbers:
NPS Corporation CHEMTREC--Domestic (800)424-9300 24 hours
3303 Spirit Way --International (202)483-7616 24 hours
Green Bay, WI 54304 Information (800) 558-5066 7:30am-4:30pm CDT M-F
Section 2. Composition/Information on Ingredients
CAS Registry # Component
497-19-8 Sodium Carbonate
72-48-0 Alizarin
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
Section 3. Hazards Identification
Emergency OverviewOdorless, white granular solid. This product presents no unusual fire hazard.
|
Potential Health Effects
Eye: May cause slight to severe irritation, possibly ulcerations.
Skin: May cause slight to severe irritation. Repeated skin contact may aggravate an existing
dermatitis (skin condition) and/or sensitivity of the skin.
Inhalation: Exposure to excessive levels of airborne dust may irritate the nose, throat,
and upper respiratory system.
Signs and Symptoms:
á Eyes: Redness, Tearing, Possible burns
á Skin: Redness, Swelling, Possible burns
á Inhalation: Discomfort of the nose and throat, Coughing, Shortness of breath
Section 4. First Aid Measures
Eyes: Immediately flush with plenty of water for at least 15 minutes. If irritation persists, seek medical
attention.
Skin: Remove contaminated clothing. Brush off excess powder with a dry towel. Wash affected area with
plenty of soap and water for several minutes. If skin irritation develops or persists, seek medical
attention.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Seek medical attention.
Ingestion: If swallowed, call a physician or poison control center immediately.
Section 5. Fire Fighting Measures
Flash Point: NA
Flammable Limits: NA
Auto-ignition Temperature: NA
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 2 of 5
KOLORSAFE¨ Dry Acid Neutralizer Revision Date: 07/20/05
MSDS No. 1008
NOTE: This material is non-combustible as supplied.
Extinguishing Media: If the need exists, dry chemical, foam, or carbon dioxide can be used.
Use water fog or spray to cool exposed equipment and containers.
Special Fire Fighting Procedures: For large fires or fires in confined areas, full emergency equipment with
self-contained breathing apparatus and full protective clothing should be
used. Thermal decomposition of this product may produce sodium
oxide and carbon dioxide gases.
Section 6. Accidental Release Measures
Avoid breathing airborne dust. Avoid contact with skin and eyes. If unused material is spilled, collect by
sweeping, shoveling or vacuuming and recycle the material for use . If this product is mixed with other
materials, see Section 13.
NOTE: Do not flush material to public sewer systems or waterways.
Section 7. Handling and Storage
Store in a cool, dry, and well ventilated area. Keep container tightly closed. Avoid contact with materials
listed in Section 10.
Section 8. Exposure Controls/Personal Protection
Exposure Limits: None specifically established for this product; treat as a nuisance dust as defined in 29 CFR
1910.1000.
OSHA PEL: Total Dust is 15 mg/M3.
Respirable Fraction is 5mg/M3.
ACGIH TLV is 5 mg/M3.
The end-user must determine the specific types of personal protective equipment needed according to 29 CFR 1910.132—Personal Protective Equipment (PPE) for General Industry. The following are only suggestions:
á Eyes: Safety glasses, goggles, or face shield
á Skin: Suitable chemically resistant gloves and protective clothing
á Inhalation: Air purifying respirator with appropriate chemical cartridge or canister
Adequate ventilation should be provided to limit the threat of inhalation.
Section 9. Physical and Chemical Properties
Appearance: White granular solid
Odor: Odorless
Boiling Point: Not Tested
Vapor Pressure (mmHg): NA
Vapor Density: NA
Solubility in Water: Slightly Soluble (30% @ 68 ¡F)
Specific Gravity (H2O=1): 2.53
Melting Point: 1564 ¡F
pH: 11.4
Evaporation Rate (Butyl Acetate=1): NA
% Vaporizable by volume (H2O=100): NA
Section 10. Stability and Reactivity
Stable: Yes
Conditions to Avoid: None known
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 3 of 5
KOLORSAFE¨ Dry Acid Neutralizer Revision Date: 07/20/05
MSDS No. 1008
Incompatibility (Materials to Avoid): Aluminum powder, fluorine, and lithium.
NOTES: This material reacts with acids, releasing large volumes of carbon dioxide gas and heat.
Reaction of this material with certain food products and their residues containing reducing sugars
can create carbon monoxide.
Hazardous Decomposition or Byproducts: Thermal decomposition may produce sodium oxide and carbon
dioxide gases.
Hazardous Polymerization: Will not occur
Section 11. Toxicological Information
This product is not listed by NTP or IARC. See Section 15.
Section 12. Ecological Information
No data available. See Section 15.
Section 13. Disposal Considerations
This product in itself is considered to be non-hazardous as defined by RCRA (40 CFR 261). Once used, this
product may take on the characteristics of the chemical(s) it was used with and should be disposed of accordingly. Disposal of this product (used or unused) must be in compliance with all local, state, and federal regulations.
Section 14. Transport Information
Not regulated by DOT
Section 15. Regulatory Information
TSCA Inventory Status: All components are listed on the TSCA list.
SARA Title III
Section 302 Extreme Hazardous Substance List: Not listed
Section 311/312 Hazard Classification:
Immediate (acute): Yes
Delayed (chronic): No
Fire: No
Sudden Release of Pressure: No
Reactive: No
Section 313 Toxic Chemicals: Not listed
USEPA CERCLA—Reportable Quantity (RQ): Not listed
RCRA Hazardous Waste: Not listed
State/IntÕl Right-to-Know Regulations: CanadaÕs WHMIS—Sodium Carbonate 1%
Section 16. Other Information
Abbreviations:
CFR: Code of Federal Regulations
OSHA: Occupational Safety and Health Administration
MSDS: Material Safety Data Sheet
PEL: Permissible Exposure Limit
NA: Not Applicable
ACGIH: American Conference of Governmental Industrial Hygienists
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 4 of 5
KOLORSAFE¨ Dry Acid Neutralizer Revision Date: 07/20/05
MSDS No. 1008
Abbreviations (cont.):
TLV: Threshold Limit Value
NTP: National Toxicology Program
IARC: International Agency for Research on Cancer
RCRA: Resource Conservation and Recovery Act
TSCA: Toxic Substances Control Act
SARA: Superfund Amendments and Reauthorization Act
USEPA: United States Environmental Protection Agency
CERCLA: Comprehensive Response, Compensation, and Liability Act
DOT: Department of Transportation
WHMIS: Workplace Hazardous Materials Information System
n.o.s.: Not Otherwise Specified
NFPA: National Fire Protection Association
HMIS: Hazardous Material Information System
NFPA Ratings: HMIS Ratings:
Health: 2 Health: 2
Fire: 0 Flammability: 0
Reactivity: 0 Reactivity: 0
Special Hazard: None Personal Protection: X
NOTE: This MSDS has been prepared only for the KOLORESAFE¨ Dry Acid Neutralizer (4400 Series) of SPILFYTER¨ Products. The MSDSÕs of the chemicals used with this product must be reviewed completely, and precautions taken as described.
The information accumulated herein has been compiled from sources believed to be reliable and is accurate to the best of our knowledge. However, NPS Corporation cannot give guarantees regarding the information from sources, and expressly does not make any warranties, nor assumes any liability for its uses of this product.
Disclaimer
You have purchased SPILFYTER¨ products from NPS Corporation
You have been provided data, product labels, MSDSÕs, and other information about SPILFYTER¨ Products.
Some SPILFYTER¨ Products are hazardous. Information about SPILFYTER¨ Products that are hazardous is furnished without guarantee. NPS Corporation does not guarantee the accuracy of the information about hazardous SPILFYTER¨ Products.
Those products are only to be used by people having expertise in using the hazardous products.
The information provided about the hazardous products is believed to be correct. You must perform your investigation as to the safety, toxicity, suitability, and proper shipping method for any hazardous SPILFYTER¨ Product.
No guarantee, expressed or implied, is made by NPS Corporation about the results of use of its products. No guarantee is made as to the safety and toxicity of any SPILFYTER¨ Product.
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 5 of 5
KOLORSAFE¨ Dry Acid Neutralizer Revision Date: 07/20/05
MSDS No. 1008
NPS Corporation does not assume any liability arising out of use of SPILFYTER¨ Products. Additional information and research may be necessary before you use the SPILFYTER¨ Products. NPS Corporation
is not responsible for damages, direct or indirect, resulting from the use of SPILFYTER¨ Products or from reliance on data in the MSDS or product label.
If you resell SPILFYTER¨ Products, you must, by law, furnish your customers a copy of MSDSÕs and handling instructions.
You are also required by law to insure that all SPILFYTER¨ Products are properly shipped.
SPILFYTER¨, KOLLECT-A-KEM¨, HANDS-IN-BAG¨, KOLORSAFE¨, and GRAB&GO¨ are all registered trademarks of NPS Corporation
AQUALOCKITª, TRUK-KIT ª, DRAINGUARDª, GAPSEALª, MEDICLEANª, and TIDYMATª are all trademarks of NPS Corporation
Copyright 2001, NPS Corporation
SPILFYTER¨ Products Page 1 of 5
KOLORSAFE¨ Dry Base Neutralizer Revision Date: 07/20/05
MSDS No. 1009
Section 1. Chemical Product and Company Identification
Product Number: 4500 Series
Product Name: KOLORSAFE¨ Dry Base Neutralizer
Manufacturer: Emergency Telephone Numbers:
NPS Corporation CHEMTREC--Domestic (800)424-9300 24 hours
3303 Spirit Way --International (202)483-7616 24 hours
Green Bay, WI 54304 Information (800) 558-5066 7:30am-4:30pm CDT M-F
Section 2. Composition/Information on Ingredients
CAS Registry # Component
77-92-9 Citric Acid, anhydrous
76-61-9 Thymol Blue
(NOTE: See Section 8 of this MSDS for Exposure Guidelines)
Section 3. Hazards Identification
Emergency OverviewOdorless, bluish-white crystalline powder. This product presents no unusual fire hazard.
|
Potential Health Effects
Eye: May cause slight to severe irritation, possibly ulcerations.
Skin: May cause slight to severe irritation. Repeated skin contact may aggravate an existing
dermatitis (skin condition) and/or sensitivity of the skin.
Inhalation: Exposure to excessive levels of airborne dust may irritate the nose, throat,
and upper respiratory system.
Signs and Symptoms:
á Eyes: Redness, Tearing, Possible burns
á Skin: Redness, Swelling, Possible burns
á Inhalation: Discomfort of the nose and throat, Coughing, Shortness of breath
Section 4. First Aid Measures
Eyes: Immediately flush with plenty of water for at least 15 minutes. If irritation persists, seek medical
attention.
Skin: Remove contaminated clothing. Brush off excess powder with a dry towel. Wash affected area with
plenty of soap and water for several minutes. If skin irritation develops or persists, seek medical
attention.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Seek medical attention.
Ingestion: If swallowed, call a physician or poison control center immediately.
Section 5. Fire Fighting Measures
Flash Point: NA
MATERIAL SAFETY DATA SHEET
SPILFYTER¨ Products Page 2 of 5
KOLORSAFE¨ Dry Base Neutralizer Revision Date: 07/20/05
MSDS No. 1009
Flammable Limits: Lower Explosive Limit (LEL): 8 gm/ft3
Upper Explosive Limit (UEL): 65 gm/ft3
Auto-ignition Temperature: 1850 ¡F
NOTE: This material is non-combustible as supplied.
Extinguishing Media: If the need exists, dry chemical, foam, or carbon dioxide can be used. Use water fog or spray to cool exposed equipment and containers.
Special Fire Fighting Procedures: For large fires or fires in confined areas, full emergency equipment with
self-contained breathing apparatus and full protective clothing should be
used. Thermal decomposition of this product may produce carbon
dioxide gas.
Section 6. Accidental Release Measures
Avoid breathing airborne dust. Avoid contact with skin and eyes. If unused material is spilled, collect by
sweeping, shoveling or vacuuming and recycle the material for use . If this product is mixed with other
materials, see Section 13.
NOTE: Do not flush material to public sewer systems or waterways.
Section 7. Handling and Storage
Store in a cool, dry, and well ventilated area. Keep container tightly closed. Avoid contact with materials listed in Section 10.
Section 8. Exposure Controls/Personal Protection
Exposure Limits: None specifically established for this product; treat as a nuisance dust as defined in 29 CFR
1910.1000.
OSHA PEL: Total Dust is 15 mg/M3.
Respirable Fraction is 5mg/M3.
ACGIH TLV: Not Established
The end-user must determine the specific types of personal protective equipment needed according to 29 CFR 1910.132—Personal Protective Equipment (PPE) for General Industry. The following are only suggestions:
á Eyes: Safety glasses, goggles, or face shield
á Skin: Suitable chemically resistant gloves and protective clothing
á Inhalation: Air purifying respirator with appropriate chemical cartridge or canister
Adequate ventilation should be provided to limit the threat of inhalation.
Section 9. Physical and Chemical Properties
&